OpenSCAD Tutorial/Chapter 9

Doing math calculations in OpenSCAD

So far you have learned that OpenSCAD variables can hold only one value throughout the execution of a script, the last value that has been assigned to them. You have also learned that a common use of OpenSCAD variables is to provide parameterization of your models. In this case every parameterized model would have a few independent variables, whose values you can change to tune that model. These variables are usually directly assigned a value as in the following examples.

Code

… wheel_diameter = 12; … body_length = 70; … wheelbase = 40; … // etc. …

Another thing that you have seen a few times already, but which has not been mentioned explicitly is the ability to perform mathematical operations using variables and hard-coded values in your script. One example of this is in implementing the car's wheelbase. Recall that the car's axles and wheels were translated along the X axis and away from the origin by half the value of the wheelbase. Since in this case the wheelbase is a variable that has already been defined in your script, you can calculate the amount of units by dividing the wheelbase variable by two. A similar thing was done with the track variable to place the left and right wheels of the car. Recall that the left and right wheels were translated along the Y axis and away from the origin by half the value of the track.

Code

axle_with_wheelset.scad use <vehicle_parts.scad> $fa = 1; $fs = 0.4; wheelbase = 40; track = 35; translate([-wheelbase/2, track/2]) simple_wheel(); translate([-wheelbase/2, -track/2]) simple_wheel(); translate([-wheelbase/2, 0, 0]) axle(track=track);

Addition, subtraction, multiplication and division are represented in OpenSCAD with the signs +, -, * and /. Apart from these fundamental operations, there are also a number of additional mathematical operations that can be useful when building more complex models. Two examples of this are the cosine and sine functions that you used to define a circular pattern of cars. Specifically, you used the cosine and sine functions to transform the polar coordinates of each car into Cartesian coordinates in order to translate it in its proper position. You can find all available math functions briefly listed in the cheat sheet.

Code

circular_pattern_of_cars.scad … r = 140; // pattern radius n = 12; // number of cars step = 360/n; for (i=[0:step:359]) { angle = i; dx = r*cos(angle); dy = r*sin(angle); translate([dx,dy,0]) rotate([0,0,angle]) car(); } …

In the above case you are not only using available mathematical operations in your script, but you are also defining two additional variables dx and dy to store the result of your calculations in order to increase the readability of your script. This is something that could also be done in your car models. Take for example the following car model.

Code

car.scad use <vehicle_parts.scad> $fa = 1; $fs = 0.4; wheelbase = 40; track = 35; // Body body(); // Front left wheel translate([-wheelbase/2,-track/2,0]) simple_wheel(); // Front right wheel translate([-wheelbase/2,track/2,0]) simple_wheel(); // Rear left wheel translate([wheelbase/2,-track/2,0]) simple_wheel(); // Rear right wheel translate([wheelbase/2,track/2,0]) simple_wheel(); // Front axle translate([-wheelbase/2,0,0]) axle(track=track); // Rear axle translate([wheelbase/2,0,0]) axle(track=track);

In the above model, mathematical operations are used to calculate the required amount of translation for each wheel and axle along the X and Y axis.

Exercise

Modify the above script in order to improve its readability and avoid repeating the same mathematical operations multiple times. To do so you should introduce two new variables named half_wheelbase and half_track. Use the corresponding mathematical calculation to set these variables equal to half the value of the wheelbase and the track variables accordingly. Replace the repeating mathematical operations in the translation commands with the use of these two variables.

Code

car_with_additional_variables.scad use <vehicle_parts.scad> $fa = 1; $fs = 0.4; wheelbase = 40; track = 35; half_wheelbase = wheelbase/2; half_track = track/2; // Body body(); // Front left wheel translate([-half_wheelbase,-half_track,0]) simple_wheel(); // Front right wheel translate([-half_wheelbase,half_track,0]) simple_wheel(); // Rear left wheel translate([half_wheelbase,-half_track,0]) simple_wheel(); // Rear right wheel translate([half_wheelbase,half_track,0]) simple_wheel(); // Front axle translate([-half_wheelbase,0,0]) axle(track=track); // Rear axle translate([half_wheelbase,0,0]) axle(track=track);

Creating any 2D object with the polygon primitive

Aside from the circle and square 2D primitives, there is another primitive that lets you design practically any 2D object. This is the polygon primitive, which lets you define 2D objects by providing a list that contains the coordinates of their points. Let’s say you want to design the following 2D part.

One way to go about designing this part without using the polygon primitive would be to start from a square that corresponds to the outer dimensions of this part and then subtract a properly rotated and translated square from its top right corner. Calculating the proper angle of rotation and amount of translation would be a time-consuming task. Additionally, following this strategy for a more complex object wouldn’t be possible. Instead, you can create this object using the polygon primitive in the following way.

Code

profile_1_polygon.scad p0 = [0, 0]; p1 = [0, 30]; p2 = [15, 30]; p3 = [35, 20]; p4 = [35, 0]; points = [p0, p1, p2, p3, p4]; polygon(points);

There are a few things you should notice regarding the use of the polygon primitive. The polygon primitive uses a list of points as inputs. The points, or vertices, are represented using pairs of X and Y coordinates, and are provided in order. When defining the list, you may start with any vertex you like and you can traverse them in either a clockwise or counterclockwise order. In the example above, the first vertex is at the origin (0,0), while the remaining vertices are listed in a clockwise direction. All vertices (pairs of X and Y coordinates) p0, p1, …, p4 are placed inside a list named points. This list is then passed to the polygon command to create the corresponding object.

Whether a variable has only a single value or it’s a list of values, you can print its content on the console using the echo command.

Code

… echo(points); …

The output in the console is: [[0, 0], [0, 30], [15, 30], [35, 20], [35, 0]]

Naming each point separately (p0, p1, …) is not required but it’s recommended to better keep track of your design. You could also directly define the list of points to be passed to the polygon command.

Code

… points = [[0, 0], [0, 30], [15, 30], [35, 20], [35, 0]]; …

Moreover, you don’t even have to define a variable to store the list of points. You can directly define the list of points when calling the polygon command.

Code

… polygon([[0, 0], [0, 30], [15, 30], [35, 20], [35, 0]]); …

The above practices are not recommended. Instead the use of additional variables as in the first example is encouraged in order to make your scripts more readable and extendable.

You could also parameterize the definition of the points’ coordinates according to the given dimensions, which will give you the ability to rapidly modify the dimensions of your object. This can be achieved by introducing one variable for each given dimension and by defining the coordinates of the points using appropriate mathematical expressions.

Code

profile_1_polygon_parametric.scad // Given dimensions d1 = 15; d2 = 20; h1 = 20; h2 = 10; // Points p0 = [0, 0]; p1 = [0, h1 + h2]; p2 = [d1, h1 + h2]; p3 = [d1 + d2, h1]; p4 = [d1 + d2, 0]; points = [p0, p1, p2, p3, p4]; // Polygon polygon(points);

Exercise

Create the following 2D object using the polygon primitive. To do this you will need to define a list that contains the pairs of X and Y coordinates of the object’s points. Remember that the points should be defined in an appropriate order. You should first store the coordinates of each point on separate variables named p0, p1, p2, … and then define a list of all points and store it in a variable named points. This list will be passed on the polygon command. The definition of each point’s coordinates should be parametric in relation to the given dimensions which can be achieved by using appropriate mathematical expressions. To do this you will also need to define a variable for each given dimension.

Code

profile_2_polygon.scad // Given dimensions h1 = 23; h2 = 10; h3 = 8; d1 = 25; d2 = 12; d3 = 15; // Points p0 = [0, 0]; p1 = [0, h1 + h2]; p2 = [d3, h1]; p3 = [d1 + d2, h1 + h2]; p4 = [d1 + d2, h3]; p5 = [d1, 0]; points = [p0, p1, p2, p3, p4, p5]; // Polygon polygon(points);

Exercise

Using the linear_extrude and rotate_extrude commands create a tube and a ring respectively that have the above profile. The tube should have a height of 100 units. The ring should have an inner diameter of 100 units. How many units do you need to translate the 2d profile along the positive direction of the X axis to achieve this?

Code

linearly_extruded_polygon.scad … linear_extrude(height=100) polygon(points); …

Code

rotationaly_extruded_polygon.scad … rotate_extrude(angle=360) translate([50,0,0]) polygon(points); …

It’s time to use your new skills to create UwU racing car!

Exercise

Create the above car body using the polygon command. To do so you will have to define each point of the design, add them all on a list and pass this list to the polygon command. The definition of each point’s coordinates should be parametric in relation to the given dimensions. Remember that in order to do this you will have to define a variable for each given dimension and calculate each point’s coordinates from these variables using appropriate mathematical expressions. You should extrude the created 2D profile to a height of 14 units.

Code

racing_car_body.scad // model parameters d1=30; d2=20; d3=20; d4=10; d5=20; w1=15; w2=45; w3=25; h=14; // right side points p0 = [0, w1/2]; p1 = [d1, w1/2]; p2 = [d1 + d2, w2/2]; p3 = [d1 + d2 + d3, w2/2]; p4 = [d1 + d2 + d3 + d4, w3/2]; p5 = [d1 + d2 + d3 + d4 + d5, w3/2]; // left side points p6 = [d1 + d2 + d3 + d4 + d5, -w3/2]; p7 = [d1 + d2 + d3 + d4, -w3/2]; p8 = [d1 + d2 + d3, -w2/2]; p9 = [d1 + d2, -w2/2]; p10 = [d1, -w1/2]; p11 = [0, -w1/2]; // all points points = [p0, p1, p2, p3, p4, p5, p6, p7, p8, p9, p10, p11]; // extruded body profile linear_extrude(height=h) polygon(points);

Exercise

As mentioned previously, you can use additional variables to increase the readability of your script and to avoid repeating mathematical operations. Can you find a way to do so in the above script?

Code

racing_car_body_with_extra_variables.scad // model parameters d1=30; d2=20; d3=20; d4=10; d5=20; w1=15; w2=45; w3=25; h=14; // distances to lengths l1 = d1; l2 = d1 + d2; l3 = d1 + d2 + d3; l4 = d1 + d2 + d3 + d4; l5 = d1 + d2 + d3 + d4 + d5; // right side points p0 = [0, w1/2]; p1 = [l1, w1/2]; p2 = [l2, w2/2]; p3 = [l3, w2/2]; p4 = [l4, w3/2]; p5 = [l5, w3/2]; // left side points p6 = [l5, -w3/2]; p7 = [l4, -w3/2]; p8 = [l3, -w2/2]; p9 = [l2, -w2/2]; p10 = [l1, -w1/2]; p11 = [0, -w1/2]; // all points points = [p0, p1, p2, p3, p4, p5, p6, p7, p8, p9, p10, p11]; // extruded body profile linear_extrude(height=h) polygon(points);

Exercise

Try completing the racing car design by adding the remaining objects to the above body.

Code

racing_car.scad use <vehicle_parts.scad> $fa = 1; $fs = 0.4; // model parameters d1=30; d2=20; d3=20; d4=10; d5=20; w1=15; w2=45; w3=25; h=14; track=40; // distances to lengths l1 = d1; l2 = d1 + d2; l3 = d1 + d2 + d3; l4 = d1 + d2 + d3 + d4; l5 = d1 + d2 + d3 + d4 + d5; // right side points p0 = [0, w1/2]; p1 = [l1, w1/2]; p2 = [l2, w2/2]; p3 = [l3, w2/2]; p4 = [l4, w3/2]; p5 = [l5, w3/2]; // left side points p6 = [l5, -w3/2]; p7 = [l4, -w3/2]; p8 = [l3, -w2/2]; p9 = [l2, -w2/2]; p10 = [l1, -w1/2]; p11 = [0, -w1/2]; // all points points = [p0, p1, p2, p3, p4, p5, p6, p7, p8, p9, p10, p11]; // extruded body profile linear_extrude(height=h) polygon(points); // canopy translate([d1+d2+d3/2,0,h]) resize([d2+d3+d4,w2/2,w2/2]) sphere(d=w2/2); // axles l_front_axle = d1/2; l_rear_axle = d1 + d2 + d3 + d4 + d5/2; half_track = track/2; translate([l_front_axle,0,h/2]) axle(track=track); translate([l_rear_axle,0,h/2]) axle(track=track); // wheels translate([l_front_axle,half_track,h/2]) simple_wheel(wheel_width=10); translate([l_front_axle,-half_track,h/2]) simple_wheel(wheel_width=10); translate([l_rear_axle,half_track,h/2]) simple_wheel(wheel_width=10); translate([l_rear_axle,-half_track,h/2]) simple_wheel(wheel_width=10);

Creating more complex object using the polygon primitive and math

From the above examples it should be quite obvious that the polygon primitive opens up possibilities to create objects that would hardly be possible by just using the fundamental 2D or 3D primitives. In these examples you created custom 2D profiles by defining the coordinates of their points according to a given design. To unlock the true power of the polygon command though, and to create even more complex and impressive designs, you have to programmatically define the points of your profiles using math. This is because defining each point separately is not scalable to the hundreds of points that are required to design smooth non-square profiles. One example of this is the following heart. Can you manually define the required points to create it? There is no way.

Instead of manually defining each point, which would be practically impossible, this model was programmatically defined using the following parametric equations.

x = 16⋅sin⁡(t)³
y = 13⋅cos⁡(t) − 5⋅cos⁡(2⋅t) − 2⋅cos⁡(3⋅t) − cos⁡(4⋅t)

When the range of the t variable covers values from 0 to 360 degrees, the above equations give the X and Y coordinates for the outline of the heart, starting from the top middle point and moving in a clockwise direction. Using the above equations, a list that contains each point’s coordinates can be generated in the following way.

Code

points = [ for (t=[0:step:359.999]) [16*pow(sin(t),3), 13*cos(t) - 5*cos(2*t) - 2*cos(3*t) - cos(4*t)]];

There are a few things you should notice about the syntax of list generation. First the name of the variable where the list will be stored is typed out. Then follows the equal sign (as in every variable assignment) and a pair of square brackets. Inside the pair of square brackets, the first thing that is typed out is the keyword for. After the keyword for follows a pair of parentheses inside of which the consecutive values that the corresponding variable is going to take are defined. This variable is similar to the for loop variable encountered in for loops. The number of elements that the generated list is going to have is equal to the number of values that this variable is going to take. For every value that this variable takes, one element of the list is defined. What each element of the list is going to be, is specified after the closing parenthesis. In this case each element of the generated list is itself a list that has two elements, one for each coordinate of the corresponding point. The t variable goes from 0 to 360 which is the required range to produce the whole outline of the heart. Since the polygon shouldn't include duplicate points, 359.999 is used instead of 360. By choosing a smaller or bigger value for the step variable, the amount of points that will be created can be controlled. Specifically, in order to create n points the step variable needs to be defined in the following way.

Code

step = 360/n;

Putting all these together, the heart can be created with the following script.

Code

heart.scad n = 500; h = 10; step = 360/n; points = [ for (t=[0:step:359.999]) [16*pow(sin(t),3), 13*cos(t) - 5*cos(2*t) - 2*cos(3*t) - cos(4*t)]]; linear_extrude(height=h) polygon(points);

You can see that by using 500 points the resolution of the outline is very good.

Exercise

Modify the above script so that the outline of the heart is consisted out of 20 points.

Code

heart_low_poly.scad … n = 20; …

Using more or less points is up to you. If you want to create an object that closely resembles the underlying mathematical equations, you should increase the number of points. Instead, if you opt for a low poly style you should decrease the number of points.

Exercise

Time for some quick list generation practice before you move on. Use the newly introduced syntax (variable = [ for (i=[start:step:end]) … ]; ) to generate the following lists: [1, 2, 3, 4, 5, 6] [10, 8, 6, 4, 2, 0, -2] [[3, 30], [4, 40], [5, 50], [6, 60]]

Solution for exercise i, [1, 2, 3, 4, 5, 6]:

Code

x = [ for (i=[1:6]) i];

Solution for exercise ii, [10, 8, 6, 4, 2, 0, -2]:

Code

x = [ for (i=[10:-2:-2]) i];

Solution for exercise iii, [[3, 30], [4, 40], [5, 50], [6, 60]]:

Code

x = [ for (i=[3:6]) [i, i*10]];

Note that when no step is provided, a default of 1 is used.

OpenSCAD also allows you to define your own mathematical functions, which can be useful when a mathematical expression is particularly long, or when you would like to use it multiple times. These functions work similarly to modules, except that instead of defining a design they define a mathematical process. After a function has been defined, you can use it by invoking its name and providing the necessary input parameters. For example, you can define a function that accepts the parameter t, and returns the X and Y coordinates of the corresponding point of the heart's outline.

Code

function heart_coordinates(t) = [16*pow(sin(t),3), 13*cos(t) - 5*cos(2*t) - 2*cos(3*t) - cos(4*t)];

In this case the script that creates the heart would take the following form.

Code

n = 500; h = 10; step = 360/n; function heart_coordinates(t) = [16*pow(sin(t),3), 13*cos(t) - 5*cos(2*t) - 2*cos(3*t) - cos(4*t)]; points = [ for (t=[0:step:359.999]) heart_coordinates(t)]; linear_extrude(height=h) polygon(points);

There are a few things you should notice about the definition of a function. First the word function is typed out. Then follows the name that you want to give to the function. In this case the function is named heart_coordinates. After the name of the function follows a pair of parentheses that contains the input parameters of the function. Like module parameters, the input parameters in a function can have default values. In this case, the only input parameter is the polar angle of the current step t and it’s not given a default value. After the closing parenthesis follows the equal sign and the command that defines the pair of X and Y coordinates of the heart’s outline.

The generation of the list of points can also be turned in a function. This can be done in a similar fashion as follows.

Code

function heart_points(n=50) = [ for (t=[0:360/n:359.999]) heart_coordinates(t)];

In this case the script that creates the heart would take the following form.

Code

n=20; h = 10; function heart_coordinates(t) = [16*pow(sin(t),3), 13*cos(t) - 5*cos(2*t) - 2*cos(3*t) - cos(4*t)]; function heart_points(n=50) = [ for (t=[0:360/n:359.999]) heart_coordinates(t)]; points = heart_points(n=n); linear_extrude(height=h) polygon(points);

In short you should remember that any command that returns a single value or a list of values can be turned into a function. Like modules, functions should be used to organize your designs and make them reusable.

Exercise

Since you have already defined the function for generating the list of points that is required to create a heart, it would be a good idea to also define a module that creates a heart. Create a module named heart. The module should have two input parameter h and n corresponding to the height of the heart and the number of points used. The module should call the heart_points function to create the required list of points and then pass that list to a polygon command to create the 2D profile of the heart. This profile should be extruded to the specified height.

Code

heart.scad … module heart(h=10, n=50) { points = heart_points(n=n); linear_extrude(height=h) polygon(points); } …

Exercise

You can save the heart_coordinates and heart_points functions along with the heart module on a script named heart.scad and add it on your libraries. Every time you want to include a heart on a design that you are working on, you can use the use command to make the functions and modules of this script available to you.

Another challenge

You are going to put your new skills into practice to create an aerodynamic spoiler for your racing car!

Exercise

You are going to use a symmetrical 4-digit NACA 00xx airfoil for your spoiler. The half thickness of such an airfoil on a given point x is given by the following formula: $y_{t}=5t(0.2969{\sqrt {x}}-0.1260x-0.3516x^{2}+0.2843x^{3}-0.1015x^{4})$ In the above formula, x is the position along the chord with 0 corresponding to the leading edge and 1 to the trailing edge, while t is the maximum thickness of the airfoil expressed as a percentage of the chord. Multiplying t by 100 gives the last two digits in the NACA 4-digit denomination. Create a function named naca_half_thickness. The function should have two input parameters: x and t. Given x and t, the function should return the half thickness of the corresponding NACA airfoil. The x and t input parameters shouldn’t have any default value.

Code

naca_airfoil_module.scad … function naca_half_thickness(x,t) = 5*t*(0.2969*sqrt(x) - 0.1260*x - 0.3516*pow(x,2) + 0.2843*pow(x,3) - 0.1015*pow(x,4)); …

Exercise

Create a function named naca_top_coordinates. This function should return a list of the X and Y coordinates for the top half of the airfoil. The first point should correspond to the leading edge while the last point should correspond to the trailing edge. The function should have two input parameters: t and n. The parameter t should correspond to the airfoil’s maximum thickness, while the parameter n should correspond to the number of created points. The list of points should be generated using an appropriate list generation command. You will need to call the naca_half_thickness function.

Code

naca_airfoil_module.scad … function naca_top_coordinates(t,n) = [ for (x=[0:1/(n-1):1]) [x, naca_half_thickness(x,t)]]; …

Exercise

Create a similar function named naca_bottom_coordinates that returns a list of points for the bottom half of the airfoil. This time the points should be given in reverse order. The first point should correspond to the trailing edge while the last point should correspond to the leading edge. This is done so that when the lists that are generated from the naca_top_coordinates and naca_bottom_coordinates functions are joined, all point of the airfoil are defined in a clockwise direction starting from the leading edge, thus making the resulting list suitable for use with the polygon command.

Code

naca_airfoil_module.scad … function naca_bottom_coordinates(t,n) = [ for (x=[1:-1/(n-1):0]) [x, - naca_half_thickness(x,t)]]; …

Exercise

Create a function named naca_coordinates that joins the two lists of points. You can use OpenSCAD's built in function “concat” to join lists together. Pass both lists as inputs to concat to join them together.

Code

naca_airfoil_module.scad … function naca_coordinates(t,n) = concat(naca_top_coordinates(t,n), naca_bottom_coordinates(t,n)); …

Exercise

Try using the naca_coordinates function to create a list that contains the points for an airfoil with a maximum thickness of 0.12 and with 300 points on each half. The list should be stored in a variable named points. The points variable should be passed to a polygon command to create the airfoils 2D profile.

Code

small_airfoil_polygon.scad … points = naca_coordinates(t,n); polygon(points); …

Exercise

The chord of the above airfoil is 1 unit. Can you use an appropriate scale command to enlarge the airfoil? The desired chord should be defined on a variable named chord and the scale command should be defined in relation to this variable. Create an airfoil that has a chord of 20 units.

Code

scaled_airfoil_polygon.scad … chord = 20; points = naca_coordinates(t=0.12,n=300); scale([chord,chord,1]) polygon(points); …

Exercise

Turn the above script into a module named naca_airfoil. The module should have three input parameter, chord, t and n. There shouldn’t be default values for any of the input parameters.

Code

naca_airfoil_module.scad module naca_airfoil(chord,t,n) { points = naca_coordinates(t,n); scale([chord,chord,1]) polygon(points); }

Exercise

All you have to do now to create a wing out of the airfoil is to apply a linear_extrude command on the 2D airfoil profile. Create a module named naca_wing that does that. The naca_wing module should have two additional input parameters compared to the naca_airfoil module, span and center. The span parameter should correspond to the height of the extrusion while the center parameter should dictate whether the extrusion is executed along only the positive direction of the Z axis or along both directions. The span parameter shouldn’t have a default value while the default value of the center parameter should be false. Can you use the naca_wing module to create the following wing? The following wing has a span of 50 units, while the airfoil of the wing has a chord of 20 units, a maximum thickness of 0.12 and 500 points on each half. You will have to additionally use a rotation transformation to place the wing as in the following image.

Code

spoiler_wing.scad … module naca_wing(span,chord,t,n,center=false) { linear_extrude(height=span,center=center) { naca_airfoil(chord,t,n); } } … rotate([90,0,0]) naca_wing(span=50,chord=20,t=0.12,n=500,center=true); …

Exercise

Use the naca_wing module to add two smaller vertical wings on the previous example in order to create the spoiler of the car. The smaller wings should have a span of 15 units as well as a chord of 15 units.

Code

spoiler.scad … rotate([90,0,0]) naca_wing(span=50,chord=20,t=0.12,n=500,center=true); translate([0,10,-15]) naca_wing(span=15,chord=15,t=0.12,n=500); translate([0,-10,-15]) naca_wing(span=15,chord=15,t=0.12,n=500); …

Exercise

Add the above spoiler on the racing car design to complete it.

Code

racing_car_with_spoiler.scad use <vehicle_parts.scad> $fa = 1; $fs = 0.4; // model parameters d1=30; d2=20; d3=20; d4=10; d5=20; w1=15; w2=45; w3=25; h=14; track=40; // distances to lengths l1 = d1; l2 = d1 + d2; l3 = d1 + d2 + d3; l4 = d1 + d2 + d3 + d4; l5 = d1 + d2 + d3 + d4 + d5; // right side points p0 = [0, w1/2]; p1 = [l1, w1/2]; p2 = [l2, w2/2]; p3 = [l3, w2/2]; p4 = [l4, w3/2]; p5 = [l5, w3/2]; // left side points p6 = [l5, -w3/2]; p7 = [l4, -w3/2]; p8 = [l3, -w2/2]; p9 = [l2, -w2/2]; p10 = [l1, -w1/2]; p11 = [0, -w1/2]; // all points points = [p0, p1, p2, p3, p4, p5, p6, p7, p8, p9, p10, p11]; // extruded body profile linear_extrude(height=h) polygon(points); // canopy translate([d1+d2+d3/2,0,h]) resize([d2+d3+d4,w2/2,w2/2]) sphere(d=w2/2); // axles l_front_axle = d1/2; l_rear_axle = d1 + d2 + d3 + d4 + d5/2; half_track = track/2; translate([l_front_axle,0,h/2]) axle(track=track); translate([l_rear_axle,0,h/2]) axle(track=track); // wheels translate([l_front_axle,half_track,h/2]) simple_wheel(wheel_width=10); translate([l_front_axle,-half_track,h/2]) simple_wheel(wheel_width=10); translate([l_rear_axle,half_track,h/2]) simple_wheel(wheel_width=10); translate([l_rear_axle,-half_track,h/2]) simple_wheel(wheel_width=10); // spoiler use <naca.scad> module car_spoiler() { rotate([90,0,0]) naca_wing(span=50,chord=20,t=0.12,n=500,center=true); translate([0,10,-15]) naca_wing(span=15,chord=15,t=0.12,n=500); translate([0,-10,-15]) naca_wing(span=15,chord=15,t=0.12,n=500); } translate([l4+d5/2,0,25]) car_spoiler();