Oberon/ETH Oberon/2.3.7/ATADisks.Mod
< Oberon | ETH Oberon
(* ETH Oberon, Copyright 1990-2003 Computer Systems Institute, ETH Zurich, CH-8092 Zurich.
Refer to the license.txt file provided with this distribution. *)
MODULE ATADisks; (** non-portable *) (* cp/pjm/prk *)
(*
Native Oberon ATA disk driver with Intel 82371SB (PIIX3) bus-mastering support (e.g. 440FX chipset).
Reference: T13/1153D Rev. 17, AT Attachment with Packet Interface Extension (ATA/ATAPI-4).
30.07.1998 cp first version working
04.12.1998 pjm added bus-mastering and restructured
23.03.1999 pjm fixed chs parameters
24.03.1999 pjm non-polling versions of PIO transfers
26.03.1999 pjm LBA mode implemented
19.04.1999 pjm Fixed for Compaq laptop
23.08.1999 prk Adding more ATAPI support
31.08.1999 pjm Modified for Disks module
*)
IMPORT SYSTEM, Kernel, Disks, PCI;
CONST
MaxControllers = 2; (* <= 10 *)
MaxDevices = 2*MaxControllers;
MaxTries = 5;
BMEnabled = TRUE; (* check for bus-master chipset *)
OverrideBIOS = TRUE; (* enable bus-master even if BIOS did not *)
PrimaryEnabled = TRUE; (* disable for testing *)
SecondaryEnabled = TRUE; (* disable for testing *)
UseConfigParams = TRUE; (* disable for testing *)
TraceStatus = TRUE; (* show error information *)
TraceIdentify = FALSE; (* show identify information *)
Experimental = TRUE; (* media handling code *)
AllowEject = TRUE; (* allow ejection of removable media *)
TraceCalls = FALSE; (* show procedures called *)
SelectWait = FALSE; (* wait before select *)
EarlyBug = TRUE; (* temporary workaround for early interrupts *)
SelectTimeout = 5000; (* ms *)
IOTimeout = 10000; (* ms *)
IdentifyTimeout = 500; (* ms *)
ResetTimeout = 1000; (* ms *)
MaxTransfer = 256; (* <= 256 *)
MaxPRD = 3; (* <= 4 *)
BS = 512;
CDRomBS = 2048;
MinLBA = 8000000; (* (> 0) if reported size larger than this, use LBA mode *)
AtapiBit = 0; RemovableBit = 1; DMABit = 2; LBABit = 3;
Packet16Bit = 4; (*packets are 16 bytes long instead of 12 - Atapi only *)
RMSNBit = 5; (*Media Status Notification supported*)
LockBit = 6; (*locking supported - RMSN only *)
EjectBit = 7; (*power eject supported - RMSN only *)
CDRom = 8; (*CDRom device - atapi only *)
ERR = 0; DRQ = 3; DRDY = 6; BSY = 7;
(*GetMediaStatus Flags*)
NM = 1; MCR = 3; MC = 5; WP = 6;
TYPE
CHS = RECORD
cyls, hds, spt: LONGINT
END;
ID = RECORD
type: SET;
ver: LONGINT;
model: ARRAY 44 OF CHAR
END;
Packet16 = ARRAY 16 OF CHAR;
PRDT = POINTER TO RECORD
prd: ARRAY MaxPRD OF RECORD (* aligned on 32-byte boundary, see Intel 290550-002 sec. 2.7.3 *)
adr, count: LONGINT
END
END;
Controller = POINTER TO RECORD
port, port2, irq, bmbase: LONGINT;
interrupts, mark: LONGINT;
prdt: PRDT;
busy: BOOLEAN
END;
Device = POINTER TO RECORD (Disks.Device)
controller: Controller;
dev: LONGINT; (* 0 or 1 *)
size: LONGINT; (* total size *)
chs: CHS; (* for controller *)
getpar: CHS; (* for GetParams *)
id: ID;
init: BOOLEAN; (* initialized? *)
sense: LONGINT; (*last device sense, atapi only*)
END;
VAR
controller: ARRAY MaxControllers OF Controller;
device: ARRAY MaxDevices OF Device;
irqs: SET;
Nunexpected, Nunknown: LONGINT; (* number of unknown/unexpected interrupts *)
PROCEDURE WriteStatus(msg: ARRAY OF CHAR; port: LONGINT);
VAR ch: CHAR; t: LONGINT;
BEGIN
IF TraceStatus THEN
Kernel.WriteString(msg); Kernel.WriteHex(port, 9);
SYSTEM.PORTIN(port+6, ch);
Kernel.WriteChar(" "); Kernel.WriteInt(ORD(ch) DIV 10H MOD 2, 1);
SYSTEM.PORTIN(port+5, ch); t := ORD(ch);
SYSTEM.PORTIN(port+4, ch); t := ASH(t, 8) + ORD(ch);
Kernel.WriteChar(" "); Kernel.WriteInt(t, 1);
SYSTEM.PORTIN(port+6, ch);
Kernel.WriteChar(" "); Kernel.WriteInt(ORD(ch) MOD 10H, 1);
SYSTEM.PORTIN(port+3, ch);
Kernel.WriteChar(" "); Kernel.WriteInt(ORD(ch), 1);
SYSTEM.PORTIN(port+1, ch);
Kernel.WriteHex(ORD(ch), -3);
SYSTEM.PORTIN(port+7, ch);
Kernel.WriteHex(ORD(ch), -3)
END
END WriteStatus;
(* Wait for specified value of controller status bits. *)
PROCEDURE WaitStatus(port: LONGINT; mask, expect, bad: SET; ms: LONGINT): BOOLEAN;
VAR t: Kernel.MilliTimer; s: SET; ch: CHAR;
BEGIN
Kernel.SetTimer(t, ms);
REPEAT
SYSTEM.PORTIN(port+7, ch); s := SYSTEM.VAL(SET, LONG(ORD(ch)))
UNTIL (s * mask = expect) OR (s * bad # {}) OR Kernel.Expired(t);
IF TraceStatus & ((s * bad # {}) OR (s * mask # expect)) THEN
WriteStatus("Status", port);
Kernel.WriteHex(SYSTEM.VAL(LONGINT, s), -3);
Kernel.WriteHex(SYSTEM.VAL(LONGINT, mask), -3);
Kernel.WriteHex(SYSTEM.VAL(LONGINT, expect), -3);
Kernel.WriteHex(SYSTEM.VAL(LONGINT, bad), -3);
Kernel.WriteChar(" "); Kernel.WriteInt(ms, 1);
Kernel.WriteLn
END;
RETURN (s * mask = expect) & (s * bad = {})
END WaitStatus;
(* Wait for specified value of controller status bits using the alternate status bits (don't clear interrupts). *)
PROCEDURE WaitAltStatus(port, port2: LONGINT; mask, expect, bad: SET; ms: LONGINT): BOOLEAN;
VAR t: Kernel.MilliTimer; s: SET; ch: CHAR;
BEGIN
Kernel.SetTimer(t, ms);
REPEAT
SYSTEM.PORTIN(port2, ch); s := SYSTEM.VAL(SET, LONG(ORD(ch)));
UNTIL (s * mask = expect) OR (s * bad # {}) OR Kernel.Expired(t);
IF TraceStatus & ((s * bad # {}) OR (s * mask # expect)) THEN
Kernel.WriteString("ATADisks: s"); Kernel.WriteHex(SYSTEM.VAL(LONGINT, s), -3);
Kernel.WriteString(", mask"); Kernel.WriteHex(SYSTEM.VAL(LONGINT, mask), -3);
Kernel.WriteString(", exp"); Kernel.WriteHex(SYSTEM.VAL(LONGINT, expect), -3);
Kernel.WriteString(", bad"); Kernel.WriteHex(SYSTEM.VAL(LONGINT, bad), -3);
Kernel.WriteString(", time "); Kernel.WriteInt(ms, 1);
Kernel.WriteLn
END;
RETURN (s * mask = expect) & (s * bad = {})
END WaitAltStatus;
(* NanoDelay - Delay at least ns nanoseconds. *)
PROCEDURE NanoDelay(ns: LONGINT);
BEGIN
ns := ns DIV 2; (* 400MHz clock => 2.5ns cycle *)
WHILE ns > 0 DO DEC(ns) END
END NanoDelay;
(* Select device for next command (0 or 1). Section 9.6. *)
PROCEDURE SelectDevice(port, d, timeout: LONGINT): LONGINT;
VAR res: LONGINT;
BEGIN
IF ~SelectWait OR WaitStatus(port, {DRQ,BSY}, {}, {}, timeout) THEN
SYSTEM.PORTOUT(port+6, CHR(ASH(d, 4)));
NanoDelay(400);
IF WaitStatus(port, {DRQ,BSY}, {}, {}, timeout) THEN res := 0 ELSE res := 2 END
ELSE
res := 1
END;
RETURN res
END SelectDevice;
(* Issue a command to the controller. *)
PROCEDURE Command(d: Device; cmd: CHAR; lba, num: LONGINT);
VAR port, sector, cylinder, head, x: LONGINT;
BEGIN
port := d.controller.port;
ASSERT((num > 0) & (num <= 100H));
SYSTEM.PORTOUT(port+2, CHR(num MOD 100H)); (* 0 means 256 *)
IF LBABit IN d.id.type THEN
ASSERT((lba >= 0) & (lba < 10000000H));
SYSTEM.PORTOUT(port+3, CHR(lba MOD 100H));
SYSTEM.PORTOUT(port+4, CHR(ASH(lba, -8) MOD 100H));
SYSTEM.PORTOUT(port+5, CHR(ASH(lba, -16) MOD 100H));
SYSTEM.PORTOUT(port+6, CHR((40H + ASH(d.dev, 4) + ASH(lba, -24) MOD 10H)))
ELSE
sector := lba MOD d.chs.spt + 1; x := lba DIV d.chs.spt;
head := x MOD d.chs.hds; cylinder := x DIV d.chs.hds;
ASSERT((sector < 100H) & (cylinder < 10000H) & (head < 10H));
SYSTEM.PORTOUT(port+3, CHR(sector));
SYSTEM.PORTOUT(port+4, CHR(cylinder MOD 100H));
SYSTEM.PORTOUT(port+5, CHR(cylinder DIV 100H));
SYSTEM.PORTOUT(port+6, CHR((ASH(d.dev, 4) + head)))
END;
SYSTEM.PORTOUT(port+7, cmd)
END Command;
(* Interrupt handler (needed for DMA operation). *)
PROCEDURE InterruptHandler;
VAR i, u, int: LONGINT; ctrl: Controller;
BEGIN
SYSTEM.STI();
SYSTEM.GETREG(SYSTEM.EBP, int); SYSTEM.GET(int+40, int);
DEC(int, Kernel.IRQ); u := 1;
FOR i := 0 TO MaxControllers-1 DO
ctrl := controller[i];
IF (ctrl # NIL) & (ctrl.irq = int) THEN u := 0; INC(ctrl.interrupts) END
END;
SYSTEM.CLI();
INC(Nunknown, u)
END InterruptHandler;
(* Wait for an interrupt to occur. *)
PROCEDURE WaitInterrupt(c: Controller; ms: LONGINT): BOOLEAN;
VAR t: Kernel.MilliTimer; ok: BOOLEAN;
BEGIN
Kernel.SetTimer(t, ms);
REPEAT ok := c.interrupts # c.mark UNTIL ok OR Kernel.Expired(t);
c.mark := c.interrupts;
RETURN ok
END WaitInterrupt;
(* Start interrupt waiting period. *)
PROCEDURE StartInterrupt(c: Controller);
BEGIN
INC(Nunexpected, c.interrupts - c.mark);
c.mark := c.interrupts
END StartInterrupt;
(* Block port input instruction. *)
PROCEDURE -RepInWord(port, bufAdr, len: LONGINT);
CODE {SYSTEM.i386}
POP ECX
POP EDI
POP EDX
CLD
REP INSW
END RepInWord;
(* Block port out instruction. *)
PROCEDURE -RepOutWord(port, bufAdr, len: LONGINT);
CODE {SYSTEM.i386}
POP ECX
POP ESI
POP EDX
CLD
REP OUTSW
END RepOutWord;
PROCEDURE WaitNotBusy(port2: LONGINT);
VAR x: CHAR;
BEGIN
SYSTEM.PORTIN(port2, x);
IF 7 IN SYSTEM.VAL(SET, LONG(ORD(x))) THEN
Kernel.WriteString("ATA: early interrupt"); Kernel.WriteHex(ORD(x), -3); Kernel.WriteLn;
(*Kernel.WriteChar(8X);*)
REPEAT
SYSTEM.PORTIN(port2, x)
UNTIL ~(7 IN SYSTEM.VAL(SET, LONG(ORD(x))))
END
END WaitNotBusy;
(* Read blocks using PIO protocol. *)
PROCEDURE ReadPIO(d: Device; lba, num, bufAdr: LONGINT): LONGINT;
VAR port, port2, res: LONGINT; x: CHAR; s: SET; c: Controller;
BEGIN
res := 0; c := d.controller; port := c.port; port2 := c.port2;
StartInterrupt(c);
Command(d, 20X, lba, num); (* read sectors *)
REPEAT
IF WaitInterrupt(c, IOTimeout) THEN
IF EarlyBug THEN WaitNotBusy(c.port2) END;
SYSTEM.PORTIN(port+7, x); s := SYSTEM.VAL(SET, LONG(ORD(x)));
IF ~(ERR IN s) THEN
RepInWord(port, bufAdr, BS DIV 2);
INC(bufAdr, BS); DEC(num)
ELSE
res := 20
END
ELSE
res := 19
END
UNTIL (num = 0) OR (res # 0);
SYSTEM.PORTIN(port2, x); (* according to spec *)
SYSTEM.PORTIN(port+7, x); s := SYSTEM.VAL(SET, LONG(ORD(x)));
IF (res = 0) & (ERR IN s) THEN res := 21 END;
IF TraceStatus & (res # 0) THEN WriteStatus("ReadPIO", port); Kernel.WriteLn END;
RETURN res
END ReadPIO;
(* Write blocks using PIO protocol. *)
PROCEDURE WritePIO(d: Device; lba, num, bufAdr: LONGINT): LONGINT;
VAR port, port2, res: LONGINT; x: CHAR; s: SET; c: Controller;
BEGIN
res := 0; c := d.controller; port := c.port; port2 := c.port2;
StartInterrupt(c);
Command(d, 30X, lba, num); (* write sectors *)
IF WaitAltStatus(port, port2, {DRQ,BSY}, {DRQ}, {ERR}, IOTimeout) THEN
REPEAT
RepOutWord(port, bufAdr, BS DIV 2);
INC(bufAdr, BS); DEC(num);
IF WaitInterrupt(c, IOTimeout) THEN
IF EarlyBug THEN WaitNotBusy(c.port2) END;
SYSTEM.PORTIN(port+7, x); s := SYSTEM.VAL(SET, LONG(ORD(x)));
IF ERR IN s THEN res := 24 END
ELSE
res := 23
END
UNTIL (num = 0) OR (res # 0)
ELSE
res := 22
END;
IF res # 0 THEN
IF TraceStatus THEN WriteStatus("WritePIO", port); Kernel.WriteLn END;
SYSTEM.PORTIN(port+7, x) (* clear interrupt *)
END;
RETURN res
END WritePIO;
(* Send packet command, atapi only *)
PROCEDURE CommandPacket(d: Device; VAR pkt: Packet16): LONGINT;
VAR res, port: LONGINT; x: CHAR; c: Controller;
BEGIN
c := d.controller; port := c.port;
SYSTEM.PORTOUT(port+1, 0X); (* no OVL, no DMA *)
SYSTEM.PORTOUT(port+2, 0X); (* tag 0 *)
SYSTEM.PORTOUT(port+4, 0FEX); (* byte count limit *)
SYSTEM.PORTOUT(port+5, 0FFX);
SYSTEM.PORTOUT(port+6, CHR(ASH(d.dev, 4))); (*device*)
SYSTEM.PORTOUT(port+7, 0A0X); (* packet *)
NanoDelay(400);
IF WaitStatus(port, {DRQ,BSY}, {DRQ}, {}, SelectTimeout) THEN
IF Packet16Bit IN d.id.type THEN
RepOutWord(port, SYSTEM.ADR(pkt[0]), 8)
ELSE
RepOutWord(port, SYSTEM.ADR(pkt[0]), 6)
END;
SYSTEM.PORTIN(c.port2, x); (* ensure status is valid *)
res := 0
ELSE
res := 31
END;
RETURN res
END CommandPacket;
(* Compose packet command, atapi only *)
PROCEDURE ComposePacket(VAR pkt: Packet16; cmd: CHAR; lba, num: LONGINT);
BEGIN
pkt[0] := cmd;
pkt[1] := 0X;
pkt[2] := CHR(ASH(lba, -24) MOD 100H);
pkt[3] := CHR(ASH(lba, -16) MOD 100H);
pkt[4] := CHR(ASH(lba, -8) MOD 100H);
pkt[5] := CHR(lba MOD 100H);
pkt[6] := 0X;
pkt[7] := CHR(ASH(num, -8) MOD 100H);
pkt[8] := CHR(num MOD 100H);
pkt[9] := 0X; pkt[10] := 0X; pkt[11] := 0X;
pkt[12] := 0X; pkt[13] := 0X; pkt[14] := 0X; pkt[15] := 0X;
END ComposePacket;
(* Transfer a packet and read/write data, atapi only *)
PROCEDURE TransferPacket(d: Device; pkt: Packet16; read: BOOLEAN; bufAdr, size: LONGINT): LONGINT;
VAR res, port, avail, key, code: LONGINT; x: CHAR;
BEGIN
port := d.controller.port;
res := CommandPacket(d, pkt);
WHILE (res = 0) & (size > 0) DO
IF WaitStatus(port, {DRQ,BSY}, {DRQ}, {ERR}, IOTimeout) THEN
SYSTEM.PORTIN(port+4, x); avail := LONG(ORD(x));
SYSTEM.PORTIN(port+5, x); avail := avail + LONG(ORD(x))*100H;
IF avail > size THEN avail := size END;
(*Kernel.WriteString("Avail = "); Kernel.WriteInt(avail, 0); Kernel.WriteChar("/"); Kernel.WriteInt(size, 0); Kernel.WriteLn;*)
IF read THEN
RepInWord(port, bufAdr, avail DIV 2)
ELSE
RepOutWord(port, bufAdr, avail DIV 2)
END;
INC(bufAdr, avail); DEC(size, avail)
ELSE
res := 33;
SYSTEM.PORTIN(port+1, x); key := ORD(x) DIV 10H;
IF key # 0 THEN
res := 34;
code := SensePacketDevice(d); d.sense := code;
(*Kernel.WriteString("Transfer -> Sense "); Kernel.WriteHex(code, 0); Kernel.WriteLn;*)
IF (key = 6) & ((code DIV 100H) = 29H) THEN (*attention + power on, ignore*)
res := CommandPacket(d, pkt) (*resubmit command*)
END
END
END
END;
IF (res = 0) & ~WaitStatus(port, {BSY, DRDY}, {DRDY}, {ERR}, IOTimeout) THEN res := 32 END;
RETURN res
END TransferPacket;
(* Sense device, packet only *)
PROCEDURE SensePacketDevice(d: Device): LONGINT;
VAR pkt: Packet16; sense, res, port: LONGINT; buf: ARRAY 18 OF CHAR;
BEGIN
port := d.controller.port;
ComposePacket(pkt, 03X, 0, 0); (* Request Sense *)
pkt[4] := 12X; (* buffer size *)
res := TransferPacket(d, pkt, TRUE, SYSTEM.ADR(buf[0]), LEN(buf));
IF res = 0 THEN
sense := ORD(buf[12])*100H + ORD(buf[13]);
ELSE
sense := ORD(buf[12])*100H + ORD(buf[13]);
Kernel.WriteString("sense failed = "); Kernel.WriteHex(sense, -5); Kernel.WriteLn;
sense := -1
END;
RETURN sense
END SensePacketDevice;
(* Read device blocksize with ModeSense command, packet only *)
PROCEDURE GetModeInfo(dev: Device; VAR blockSize: LONGINT): LONGINT;
VAR pkt: Packet16; buf: ARRAY 12 OF CHAR; res, port(*, size*): LONGINT;
BEGIN
port := dev.controller.port;
ComposePacket(pkt, 1AX, 0, 0); (*ModeSense*)
pkt[2] := 3FX; (*mode page: all pages*)
pkt[4] := 0CX; (*buffer size*)
(*
ComposePacket(pkt, 5AX(*1AX*), 0, 0); (*ModeSense10*)
pkt[2] := 0BFX(*3FX*); (*default values + mode page: all pages*)
pkt[8(*4*)] := 0CX; (*buffer size*)
*)
res := TransferPacket(dev, pkt, TRUE, SYSTEM.ADR(buf[0]), LEN(buf));
IF (res = 34) & (dev.sense = 2800H) THEN (*failed because of media change, repeat*)
res := TransferPacket(dev, pkt, TRUE, SYSTEM.ADR(buf[0]), LEN(buf))
END;
IF (res = 0) & (ORD(buf[3]) = 8) THEN (*if one descriptor returned*)
blockSize := ORD(buf[4+7]);
blockSize := blockSize + SYSTEM.LSH(ORD(buf[4+5]), 16);
blockSize := blockSize + SYSTEM.LSH(ORD(buf[4+6]), 8);
(*size := ORD(buf[4+3]);
size := size + SYSTEM.LSH(ORD(buf[4+2]), 16);
size := size + SYSTEM.LSH(ORD(buf[4+1]), 8);*)
ELSE
blockSize := 0;
(*size := 0;*)
END;
IF blockSize = 0 THEN
Kernel.WriteString("GetModeInfo "); Kernel.WriteString(dev.name);
Kernel.WriteChar(" "); Kernel.WriteInt(blockSize, 1); Kernel.WriteLn;
blockSize := BS
END;
RETURN res
END GetModeInfo;
(* Read medium capacity, packet only *)
PROCEDURE ReadCapacity(d: Device; VAR blkSize, size: LONGINT): LONGINT;
VAR pkt: Packet16; buf: ARRAY 8 OF CHAR; res, port: LONGINT;
BEGIN
IF TraceCalls THEN Kernel.WriteString("ReadCapacity"); Kernel.WriteLn END;
port := d.controller.port;
ComposePacket(pkt, 25X, 0, 0); (* read capacity *)
res := TransferPacket(d, pkt, TRUE, SYSTEM.ADR(buf[0]), LEN(buf));
IF (res = 34) & (d.sense = 0401H) THEN (*failed because getting ready, repeat*)
NanoDelay(1000); (*wait a little*)
REPEAT res := TransferPacket(d, pkt, TRUE, SYSTEM.ADR(buf[0]), LEN(buf)) UNTIL (res = 0) OR (d.sense # 0401H)
END;
IF (res = 34) & (d.sense = 2800H) THEN (*failed because of media change, repeat*)
res := TransferPacket(d, pkt, TRUE, SYSTEM.ADR(buf[0]), LEN(buf))
END; (*yes, error 2800H may follow 0401H*)
IF res = 0 THEN
size := 1 + ASH(LONG(ORD(buf[0])), 24) + ASH(LONG(ORD(buf[1])), 16);
size := size + ASH(LONG(ORD(buf[2])), 8) + LONG(ORD(buf[3]));
blkSize := ASH(LONG(ORD(buf[4])), 24) + ASH(LONG(ORD(buf[5])), 16);
blkSize := blkSize + ASH(LONG(ORD(buf[6])), 8) + LONG(ORD(buf[7]));
IF (CDRom IN d.id.type) & (blkSize # 2048) THEN
Kernel.WriteString(d.name); Kernel.WriteString(" block size set to 2048, was ");
Kernel.WriteInt(blkSize, 0); Kernel.WriteLn;
blkSize := 2048
END;
IF TraceIdentify THEN
Kernel.WriteString("ATADisks: read capacity ");
Kernel.WriteInt(size, 4); Kernel.WriteString(" * ");
Kernel.WriteInt(blkSize, 4); Kernel.WriteString(" = ");
Kernel.WriteInt(size * (blkSize DIV 512) DIV 2048, 4); Kernel.WriteString(" MB");
Kernel.WriteLn
END
END;
RETURN res
END ReadCapacity;
(* test unit ready, packet only *)
PROCEDURE TestUnitReady(d: Device): LONGINT;
VAR port, res: LONGINT; pkt: Packet16;
BEGIN
IF TraceCalls THEN Kernel.WriteString("TestUnitReady"); Kernel.WriteLn END;
port := d.controller.port;
ComposePacket(pkt, 0X, 0, 0); (* test unit ready command *)
res := TransferPacket(d, pkt, FALSE, 0, 0);
RETURN res
END TestUnitReady;
(* set CDRom Speed *)
(*
PROCEDURE SetCDSpeed(dev: Device; read, write: LONGINT);
VAR res, port: LONGINT; pkt: Packet16;
BEGIN
port := dev.controller.port;
ComposePacket(pkt, 0BBX, 0, 0); (* set cd-rom speed command *)
pkt[2] := CHR(ASH(read, -8) MOD 100H);
pkt[3] := CHR(read MOD 100H);
pkt[4] := CHR(ASH(write, -8) MOD 100H);
pkt[5] := CHR(write MOD 100H);
res := TransferPacket(dev, pkt, FALSE, 0, 0);
IF res # 0 THEN
Kernel.WriteString("SetSpeed failed "); Kernel.WriteHex(SensePacketDevice(dev), 0); Kernel.WriteLn
END;
END SetCDSpeed;
*)
(* lock/unlock media *)
PROCEDURE LockMedium(d: Device; lock: BOOLEAN): LONGINT;
VAR port, res: LONGINT; pkt: Packet16;
BEGIN
IF Experimental THEN
port := d.controller.port;
IF AtapiBit IN d.id.type THEN
ComposePacket(pkt, 1EX, 0, 0); (* allow medium removal *)
IF lock THEN pkt[4] := 1X END;
res := TransferPacket(d, pkt, FALSE, 0, 0);
RETURN res
ELSE
res := SelectDevice(port, d.dev, SelectTimeout);
IF res = 0 THEN
IF lock THEN
SYSTEM.PORTOUT(port+7, 0DEX) (* media lock *)
ELSE
SYSTEM.PORTOUT(port+7, 0DFX) (* media unlock *)
END;
NanoDelay(400);
IF ~WaitStatus(port, {BSY}, {}, {ERR}, ResetTimeout) THEN res := 29 END
END
END
ELSE
RETURN Disks.Unsupported
END
END LockMedium;
(* eject media *)
PROCEDURE RemoveMedium(d: Device): LONGINT;
VAR port, res: LONGINT; pkt: Packet16;
BEGIN
port := d.controller.port;
IF AtapiBit IN d.id.type THEN
ComposePacket(pkt, 01BX, 0, 0); (* StartStopUnit *)
pkt[4] := 2X; (*eject*)
res := TransferPacket(d, pkt, FALSE, 0, 0);
ELSE
SYSTEM.PORTOUT(port+6, CHR((ASH(d.dev, 4))));
SYSTEM.PORTOUT(port+7, 0EDX); (* media eject *)
NanoDelay(400);
IF ~WaitStatus(port, {BSY}, {}, {ERR}, ResetTimeout) THEN res := 39 END
END;
RETURN res
END RemoveMedium;
(* get the media status, RMSN only *)
PROCEDURE GetMediaStatus(dev: Device; VAR status: SET): LONGINT;
VAR port, res: LONGINT; ch: CHAR;
BEGIN
port := dev.controller.port;
SYSTEM.PORTOUT(port+6, CHR((ASH(dev.dev, 4))));
SYSTEM.PORTOUT(port+7, 0DAX); (* get media status *)
IF WaitStatus(port, {BSY}, {}, {}, ResetTimeout) THEN
res := 0;
SYSTEM.PORTIN(port+1, ch); status := SYSTEM.VAL(SET, LONG(ORD(ch)))
ELSE
res := 38;
ch := 0X; status := {}
END;
RETURN res
END GetMediaStatus;
(* switch on/off RMSN, RMSN only *)
PROCEDURE SetRMSN(dev: Device; on: BOOLEAN): LONGINT;
VAR port, res: LONGINT; ch: CHAR;
BEGIN
IF Experimental THEN
port := dev.controller.port;
(*WriteStatus("SetRMSN", port); Kernel.WriteLn;*)
res := SelectDevice(port, dev.dev, IdentifyTimeout);
IF res = 0 THEN
IF on THEN
SYSTEM.PORTOUT(port+1, 95X) (* enable media status notification *)
ELSE
SYSTEM.PORTOUT(port+1, 31X) (* disable media status notification *)
END;
SYSTEM.PORTOUT(port+4, 0X);
SYSTEM.PORTOUT(port+5, 0X);
SYSTEM.PORTOUT(port+7, 0EFX); (* set features *)
NanoDelay(400);
IF WaitStatus(port, {BSY}, {}, {ERR}, ResetTimeout) THEN
res := 0;
Kernel.WriteString(dev.name); Kernel.WriteString(": enable RMSN with:");
SYSTEM.PORTIN(port+5, ch);
IF 0 IN SYSTEM.VAL(SET, ch) THEN Kernel.WriteString(" PENA") END;
IF 1 IN SYSTEM.VAL(SET, ch) THEN INCL(dev.id.type, LockBit); Kernel.WriteString(" LOCK") END;
IF 2 IN SYSTEM.VAL(SET, ch) THEN INCL(dev.id.type, EjectBit); Kernel.WriteString(" PEJ") END;
Kernel.WriteLn
ELSE
res := 35;
Kernel.WriteString(dev.name); Kernel.WriteString(": device doesn't support RMSN");
SYSTEM.PORTIN(port+5, ch); Kernel.WriteHex(ORD(ch), -3);
Kernel.WriteLn
END
END
ELSE
res := 0
END;
RETURN res
END SetRMSN;
(* Check if media has changed and update it, removable only *)
PROCEDURE CheckRemovable(dev: Device; read: BOOLEAN; lba, num: LONGINT): LONGINT;
VAR port, res, code, blockSize: LONGINT; status: SET; changed: BOOLEAN;
BEGIN
port := dev.controller.port; changed := FALSE;
IF RMSNBit IN dev.id.type THEN
res := GetMediaStatus(dev, status);
IF res = 0 THEN
IF NM IN status THEN
res := Disks.MediaMissing
ELSIF AllowEject & (MCR IN status) THEN (*remove request*)
res := RemoveMedium(dev);
IF res = 0 THEN
REPEAT res := GetMediaStatus(dev, status) UNTIL (res # 0) OR (NM IN status);
dev.size := 0; res := Disks.MediaMissing;
EXCL(dev.flags, Disks.ReadOnly)
END
ELSIF (MC IN status) OR (dev.size = 0) THEN
res := ReadCapacity(dev, blockSize, dev.size);
ASSERT((res # 0) OR (blockSize = dev.blockSize));
IF WP IN status THEN INCL(dev.flags, Disks.ReadOnly) ELSE EXCL(dev.flags, Disks.ReadOnly) END;
changed := TRUE;
END
END
ELSIF AtapiBit IN dev.id.type THEN
res := TestUnitReady(dev);
IF res = 34 THEN
code := dev.sense
ELSIF (res = 0) OR (res = 32) THEN
code := SensePacketDevice(dev)
ELSE
code := 0;
END;
IF code = 0 THEN
IF dev.size = 0 THEN
res := ReadCapacity(dev, dev.blockSize, dev.size); changed := TRUE;
IF dev.blockSize = 0 THEN dev.blockSize := blockSize END
END (*first time*)
ELSIF code = 2800H THEN (* medium may have changed *)
res := ReadCapacity(dev, blockSize, dev.size); changed := TRUE;
IF dev.blockSize = 0 THEN dev.blockSize := blockSize END
ELSIF code = 3A00H THEN (* medium not present *)
res := Disks.MediaMissing;
ELSIF code = -1 THEN
res := Disks.MediaMissing
ELSE
res := Disks.Unsupported;
Kernel.WriteString("Check/Unknown Sense "); Kernel.WriteHex(code, 0); Kernel.WriteLn;
END
ELSE
res := Disks.Unsupported
END;
IF (res # 0) OR (num = 0) THEN
(*skip*)
ELSIF (lba >= dev.size) OR (lba+num > dev.size) THEN (* out of range *)
res := 226
ELSIF ~read & (WP IN status) THEN (* write protected *)
res := 28
ELSIF changed THEN
res := Disks.MediaChanged
END;
RETURN res
END CheckRemovable;
(* Transfer blocks using DMA. *)
PROCEDURE TransferDMA(d: Device; read: BOOLEAN; lba, num, bufAdr: LONGINT): LONGINT;
VAR port, res, bmbase, i, size, left: LONGINT; x: CHAR; s: SET; c: Controller;
BEGIN
ASSERT(~ODD(bufAdr)); (* transfer must be word-aligned *)
ASSERT((num > 0) & (num <= MaxTransfer));
res := 0; c := d.controller;
port := c.port; bmbase := c.bmbase; ASSERT(bmbase # 0);
(* init prdt *)
i := 0; size := num*BS;
REPEAT
left := 10000H - bufAdr MOD 10000H; (* bytes left until next 64k boundary *)
IF left > size THEN left := size END;
c.prdt.prd[i].adr := bufAdr; c.prdt.prd[i].count := left;
INC(bufAdr, left); DEC(size, left); INC(i)
UNTIL size = 0;
INCL(SYSTEM.VAL(SET, c.prdt.prd[i-1].count), 31); (* end marker *)
(* init dma *)
SYSTEM.PORTOUT(bmbase+4, SYSTEM.ADR(c.prdt.prd[0]));
IF read THEN s := {3} ELSE s := {} END;
SYSTEM.PORTOUT(bmbase, SYSTEM.VAL(CHAR, s)); (* set direction *)
SYSTEM.PORTIN(bmbase+2, x);
s := SYSTEM.VAL(SET, LONG(ORD(x)));
SYSTEM.PORTOUT(bmbase+2, CHR(SYSTEM.VAL(LONGINT, s + {1,2}))); (* clear error, interrupt by writing *)
(* init transfer *)
StartInterrupt(c);
IF read THEN x := 0C8X ELSE x := 0CAX END; (* read dma or write dma *)
Command(d, x, lba, num);
SYSTEM.PORTIN(bmbase, x);
s := SYSTEM.VAL(SET, LONG(ORD(x)));
SYSTEM.PORTOUT(bmbase, CHR(SYSTEM.VAL(LONGINT, s + {0}))); (* start bm *)
IF WaitInterrupt(c, IOTimeout) THEN
IF EarlyBug THEN WaitNotBusy(c.port2) END;
SYSTEM.PORTIN(bmbase+2, x); (* check dma status *)
s := SYSTEM.VAL(SET, LONG(ORD(x)));
IF 1 IN s THEN res := 8 END
ELSE
res := 7
END;
SYSTEM.PORTIN(bmbase, x);
s := SYSTEM.VAL(SET, LONG(ORD(x)));
SYSTEM.PORTOUT(bmbase, CHR(SYSTEM.VAL(LONGINT, s - {0}))); (* stop bm *)
SYSTEM.PORTIN(port+7, x); (* clear interrupt *)
s := SYSTEM.VAL(SET, LONG(ORD(x)));
IF (res = 0) & (ERR IN s) THEN res := 9 END;
RETURN res
END TransferDMA;
(* Initialize/Reset the selected device. *)
PROCEDURE InitDevice(port, port2, dev: LONGINT; type: SET; chs: CHS): LONGINT;
VAR x: CHAR; sector, head, res: LONGINT;
BEGIN
IF AtapiBit IN type THEN
res := 0
ELSE
sector := chs.spt;
head := chs.hds;
SYSTEM.PORTOUT(port+2, CHR(sector));
SYSTEM.PORTOUT(port+3, 0X);
SYSTEM.PORTOUT(port+4, 0X);
SYSTEM.PORTOUT(port+5, 0X);
SYSTEM.PORTOUT(port+6, CHR((ASH(dev, 4) + (head-1) MOD 10H)));
SYSTEM.PORTOUT(port+7, 091X); (* initialize device parameters *)
SYSTEM.PORTIN(port2, x);
IF ~WaitStatus(port, {BSY}, {}, {ERR}, ResetTimeout) THEN
IF LBABit IN type THEN
Kernel.WriteString("ATADisks: using LBA mode, init dev param ignored");
Kernel.WriteLn
ELSE
res := 17
END
END
END;
RETURN res
END InitDevice;
(* Convert a string to an integer. *)
PROCEDURE StrToInt(VAR i: LONGINT; VAR s: ARRAY OF CHAR): LONGINT;
VAR vd, vh, sgn, d: LONGINT; hex: BOOLEAN;
BEGIN
vd := 0; vh := 0; hex := FALSE;
IF s[i] = "-" THEN sgn := -1; INC(i) ELSE sgn := 1 END;
LOOP
IF (s[i] >= "0") & (s[i] <= "9") THEN d := ORD(s[i])-ORD("0")
ELSIF (CAP(s[i]) >= "A") & (CAP(s[i]) <= "F") THEN d := ORD(CAP(s[i]))-ORD("A")+10; hex := TRUE
ELSE EXIT
END;
vd := 10*vd + d; vh := 16*vh + d;
INC(i)
END;
IF CAP(s[i]) = "H" THEN hex := TRUE; INC(i) END; (* optional H *)
IF hex THEN vd := vh END;
RETURN sgn * vd
END StrToInt;
(* Initialize controller parameters. *)
PROCEDURE ParseControllerConfig(num, dirq, dc: LONGINT);
VAR s: ARRAY 32 OF CHAR; id: ARRAY 8 OF CHAR; p, c, r, irq: LONGINT;
BEGIN
id := "IDE#"; id[3] := CHR(ORD("0") + num);
Kernel.GetConfig(id, s);
IF (num = 0) & (s = "") THEN Kernel.GetConfig("IDE", s) END;
IF UseConfigParams & (s # "") THEN
p := 0; c := 0; r := 0;
irq := StrToInt(p, s);
IF (irq # 0) & (s[p] = ",") THEN
INC(p); c := StrToInt(p, s);
IF s[p] = "," THEN
INC(p); r := StrToInt(p, s)
END;
IF c = 0 THEN c := dc END;
IF (r = 0) & (c > 0) THEN r := c + 206H END
END
ELSE
irq := dirq; c := dc; r := c + 206H
END;
IF c > 0 THEN
NEW(controller[num]);
controller[num].port := c; controller[num].port2 := r; controller[num].irq := irq;
controller[num].bmbase := 0 (* BM disabled *)
END
END ParseControllerConfig;
(* Get hard disk parameters. *)
PROCEDURE GetPar(p: LONGINT; ofs: LONGINT): LONGINT;
VAR x: CHAR;
BEGIN
SYSTEM.GET(p+12+ofs, x);
RETURN ORD(x)
END GetPar;
(* Parse hard disk parameters of first two drives from BIOS. *)
PROCEDURE GetKernelCHS(d: LONGINT; VAR chs1: CHS);
VAR p, t, i : LONGINT; chs: CHS;
BEGIN
p := Kernel.bt; i := 0;
LOOP
SYSTEM.GET(p, t);
IF t = -1 THEN EXIT (* end *)
ELSIF t = 5 THEN (* HD params *)
IF i = d THEN
chs.cyls := GetPar(p, 0) + 100H*GetPar(p, 1);
chs.hds := GetPar(p, 2); chs.spt := GetPar(p, 14);
IF chs.cyls * chs.hds * chs.spt > 0 THEN chs1 := chs END
END;
INC(i)
END;
SYSTEM.GET(p+4, t); INC(p, t)
END
END GetKernelCHS;
(* Convert an ATA identify string to a readable format. *)
PROCEDURE GetATAString(VAR buf: ARRAY OF INTEGER; from, to: LONGINT; VAR s: ARRAY OF CHAR);
VAR i, j: LONGINT;
BEGIN
FOR i := from TO to DO
s[2*(i-from)] := CHR(buf[i] DIV 100H MOD 100H);
s[2*(i-from)+1] := CHR(buf[i] MOD 100H)
END;
s[2*(to-from+1)] := 0X;
i := 0; j := 0;
WHILE s[i] # 0X DO
IF (s[i] >= 20X) & (s[i] <= 7EX) THEN s[j] := s[i]; INC(j) END;
INC(i);
IF (j # 0) & (s[j-1] = 20X) THEN
WHILE s[i] = 20X DO INC(i) END
END
END;
IF (j # 0) & (s[j-1] = 20X) THEN DEC(j) END;
s[j] := 0X
END GetATAString;
(* Identify an Atapi packet device. *)
PROCEDURE IdentifyAtapi(port, port2: LONGINT; VAR id: ID): LONGINT;
VAR res: LONGINT; x: CHAR; buf: ARRAY BS DIV 2 OF INTEGER;
BEGIN
SYSTEM.PORTOUT(port+7, 0A1X); (* identify ATAPI device *)
SYSTEM.PORTIN(port2, x); (* ensure status ok *)
IF WaitStatus(port, {BSY}, {}, {}, IdentifyTimeout) THEN
INCL(id.type, AtapiBit);
RepInWord(port, SYSTEM.ADR(buf[0]), BS DIV 2);
IF 0 IN SYSTEM.VAL(SET, LONG(buf[0])) THEN INCL(id.type, Packet16Bit) END;
IF 7 IN SYSTEM.VAL(SET, LONG(buf[0])) THEN INCL(id.type, RemovableBit) END;
IF SYSTEM.VAL(SET, LONG(buf[0])) * {8..12} = {8, 10} THEN INCL(id.type, CDRom) END;
IF 8 IN SYSTEM.VAL(SET, LONG(buf[49])) THEN INCL(id.type, DMABit) END;
IF SYSTEM.VAL(SET, LONG(buf[127])) * {0,1} = {0} THEN INCL(id.type, RMSNBit) END;
GetATAString(buf, 27, 46, id.model);
IF (buf[80] # -1) & (buf[81] # -1) THEN
id.ver := ASH(LONG(buf[80]) MOD 10000H, 16) + LONG(buf[81]) MOD 10000H
END;
res := 0
ELSE
res := 12
END;
RETURN res
END IdentifyAtapi;
(* Identify an ATA device. *)
PROCEDURE IdentifyATA(port: LONGINT; VAR chs: CHS; VAR size: LONGINT; VAR id: ID): LONGINT;
VAR res, size1: LONGINT; buf: ARRAY BS DIV 2 OF INTEGER;
BEGIN
RepInWord(port, SYSTEM.ADR(buf[0]), BS DIV 2);
(*Kernel.WriteMemory(SYSTEM.ADR(buf[0]), BS);*)
chs.cyls := LONG(buf[1]) MOD 10000H;
chs.hds := LONG(buf[3]) MOD 10000H;
chs.spt := LONG(buf[6]) MOD 10000H;
size := ASH(LONG(buf[61]) MOD 10000H, 16) + LONG(buf[60]) MOD 10000H;
IF size >= MinLBA THEN INCL(id.type, LBABit) END;
size1 := chs.cyls * chs.hds * chs.spt;
IF size < size1 THEN size := size1 END;
IF SYSTEM.VAL(SET, LONG(buf[0])) * {6,7} = {7} THEN INCL(id.type, RemovableBit) END;
IF SYSTEM.VAL(SET, LONG(buf[127])) * {0,1} = {0} THEN INCL(id.type, RMSNBit) END;
INCL(id.type, DMABit); (* DMA support mandatory in ATA/ATAPI-4 *)
GetATAString(buf, 27, 46, id.model);
IF (buf[80] # -1) & (buf[81] # -1) THEN
id.ver := ASH(LONG(buf[80]) MOD 10000H, 16) + LONG(buf[81]) MOD 10000H
END;
IF (chs.hds <= 16) & (chs.spt <= 255) THEN res := 0 ELSE res := 25 END;
RETURN res
END IdentifyATA;
(* Identify a device. *)
PROCEDURE IdentifyDevice(controller: Controller; dev: LONGINT; VAR chs: CHS; VAR size: LONGINT; VAR id: ID): LONGINT;
VAR res, port, port2: LONGINT; x: CHAR; t: Kernel.MilliTimer; zip: ARRAY 12 OF CHAR;
BEGIN
id.type := {}; id.ver := 0; chs.cyls := 0; chs.hds := 0; chs.spt := 0; size := 0;
port := controller.port; port2 := controller.port2;
IF port # 0 THEN
Kernel.SetTimer(t, 50); REPEAT UNTIL Kernel.Expired(t);
res := SelectDevice(port, dev, IdentifyTimeout);
IF res = 0 THEN
StartInterrupt(controller);
SYSTEM.PORTOUT(port+7, 0ECX); (* identify device *)
IF WaitInterrupt(controller, IdentifyTimeout) THEN
IF EarlyBug THEN WaitNotBusy(controller.port2) END;
SYSTEM.PORTIN(port+5, x); (* signature byte *)
IF x = 0EBX THEN
res := IdentifyAtapi(port, port2, id);
(* hack to make bootable zips (should write code to detect geometry) *)
COPY(id.model, zip); zip[10] := 0X;
IF zip = "IOMEGA ZIP" THEN
chs.hds := 40H; chs.spt := 20H;
IF id.model[11] = "2" THEN chs.cyls := 239 ELSE chs.cyls := 96 END;
END
ELSE
res := IdentifyATA(port, chs, size, id);
IF (res = 0) & (size = 0) THEN res := 13 END
END
ELSE
res := 14
END
END;
Kernel.SetTimer(t, 50); REPEAT UNTIL Kernel.Expired(t);
SYSTEM.PORTOUT(port+6, 0X); (* select device 0 again *)
NanoDelay(400)
ELSE
res := 15
END;
RETURN res
END IdentifyDevice;
(* Clean up unloaded module. *)
PROCEDURE Cleanup;
VAR i: LONGINT; d: Device;
BEGIN
IF Kernel.shutdown = 0 THEN
FOR i := 0 TO MaxDevices-1 DO
d := device[i];
IF d # NIL THEN Disks.Unregister(d) END
END;
FOR i := 0 TO 15 DO
IF i IN irqs THEN
EXCL(irqs, i);
Kernel.RemoveIP(InterruptHandler, SHORT(Kernel.IRQ + i))
END
END
END
END Cleanup;
(* Initialization. *)
PROCEDURE IdentifyControllers;
VAR i: LONGINT;
BEGIN
FOR i := 0 TO MaxControllers-1 DO controller[i] := NIL END;
IF PrimaryEnabled THEN ParseControllerConfig(0, 14, 01F0H) END;
IF SecondaryEnabled THEN ParseControllerConfig(1, 15, 0170H) END;
IF MaxControllers > 2 THEN (* compile-time expression *)
FOR i := 2 TO MaxControllers-1 DO ParseControllerConfig(i, 0, 0) END
END
END IdentifyControllers;
PROCEDURE ResetController(ctrl: Controller): BOOLEAN;
VAR t: Kernel.MilliTimer;
BEGIN
SYSTEM.PORTOUT(ctrl.port2, 4X); (* reset controller *)
Kernel.SetTimer(t, 1); REPEAT UNTIL Kernel.Expired(t); (* wait > 4.8us *)
SYSTEM.PORTOUT(ctrl.port2, 8X);
RETURN WaitStatus(ctrl.port, {BSY}, {}, {}, ResetTimeout)
END ResetController;
PROCEDURE IdentifyDevices;
VAR
p, q, a, n, res, size, tmp: LONGINT; ctrl: Controller; dev: Device; chs: CHS; id: ID; x: CHAR;
name: Disks.Name; s: ARRAY 16 OF CHAR; useBIOS: BOOLEAN;
BEGIN
Kernel.GetConfig("ATABIOS", s);
useBIOS := s[0] = "1";
IF useBIOS THEN
Kernel.WriteString("Using BIOS geometry"); Kernel.WriteLn
END;
(* identify all devices *)
a := 0; n := 0;
FOR p := 0 TO MaxDevices-1 DO
ctrl := controller[p DIV 2];
IF ctrl # NIL THEN
name := "IDEx"; name[3] := CHR(48 + p);
res := IdentifyDevice(ctrl, p MOD 2, chs, size, id);
IF res = 0 THEN
NEW(dev); Disks.InitDevice(dev, name);
dev.controller := ctrl; dev.dev := p MOD 2; dev.init := FALSE;
dev.id := id; dev.size := size; dev.chs := chs; dev.getpar := dev.chs;
COPY(id.model, dev.desc);
IF AtapiBit IN id.type THEN
SYSTEM.PORTOUT(ctrl.port+6, CHR(ASH(dev.dev, 4)));
SYSTEM.PORTOUT(ctrl.port+7, 8X); (* reset packet device *)
SYSTEM.PORTIN(ctrl.port2, x);
IF ~WaitStatus(ctrl.port, {BSY}, {}, {}, ResetTimeout) THEN res := 16 END;
res := TestUnitReady(dev);
IF res # 0 THEN tmp := SensePacketDevice(dev); res := 0 END;
IF CDRom IN id.type THEN
(*SetCDSpeed(dev, 0FFFFH, 0FFFFH);*) (* use the maximal speed *)
dev.blockSize := CDRomBS (* ATAPI/CDRom shall all use this size *)
ELSE res := GetModeInfo(dev, dev.blockSize) (* detect block size *)
END;
IF (res = 0) & ~(RemovableBit IN dev.id.type) THEN res := ReadCapacity(dev, tmp, dev.size) END
ELSE
dev.blockSize := BS;
IF (p < 2) & useBIOS THEN GetKernelCHS(p, dev.getpar) END; (* override CHS *)
IF dev.size > 16383*16*63 THEN
dev.getpar.cyls := dev.size DIV (dev.getpar.hds * dev.getpar.spt)
END
END;
device[q] := dev; INC(q);
IF (res = 0) & (RMSNBit IN id.type) THEN
res := SetRMSN(dev, TRUE);
(*IF res # 0 THEN EXCL(dev.id.type, RMSNBit) END*)
END
ELSE (* skip *)
END;
IF TraceIdentify THEN
Kernel.WriteString(name); Kernel.WriteString(": Identify = ");
Kernel.WriteInt(res, 1); Kernel.WriteLn
END;
IF ~ResetController(ctrl) THEN
Kernel.WriteString(name); Kernel.WriteString(": reset failed"); Kernel.WriteLn
ELSIF TraceIdentify THEN
Kernel.WriteString(name); Kernel.WriteString(": reset ok"); Kernel.WriteLn
END
END
END;
WHILE q # MaxDevices DO device[q] := NIL; INC(q) END
END IdentifyDevices;
PROCEDURE ShowCHS(chs: CHS);
BEGIN
Kernel.WriteInt(chs.cyls, 1);
Kernel.WriteChar("*");
Kernel.WriteInt(chs.hds, 1);
Kernel.WriteChar("*");
Kernel.WriteInt(chs.spt, 1)
END ShowCHS;
PROCEDURE ShowDevices;
VAR i, j: LONGINT; dev: Device;
BEGIN
FOR i := 0 TO MaxDevices-1 DO
dev := device[i];
IF dev # NIL THEN
j := 0; WHILE controller[j] # dev.controller DO INC(j) END;
Kernel.WriteString("IDE"); Kernel.WriteInt(j*2 + dev.dev, 1);
IF AtapiBit IN dev.id.type THEN
Kernel.WriteString(", packet");
IF Packet16Bit IN dev.id.type THEN Kernel.WriteString("16") ELSE Kernel.WriteString("12") END;
ELSE
Kernel.WriteString(", "); Kernel.WriteInt(dev.size DIV 2048, 1); Kernel.WriteString("MB");
Kernel.WriteString(", "); ShowCHS(dev.chs);
IF (dev.getpar.cyls # dev.chs.cyls) OR (dev.getpar.hds # dev.chs.hds) OR (dev.getpar.spt # dev.chs.spt) THEN
Kernel.WriteString(", ("); ShowCHS(dev.getpar); Kernel.WriteChar(")")
END
END;
IF RemovableBit IN dev.id.type THEN Kernel.WriteString(", removable") END;
IF RMSNBit IN dev.id.type THEN Kernel.WriteString(", RMSN") END;
IF ~(DMABit IN dev.id.type) THEN Kernel.WriteString(", no DMA") END;
IF LBABit IN dev.id.type THEN Kernel.WriteString(", LBA") END;
Kernel.WriteString(", "); Kernel.WriteString(dev.id.model);
IF dev.id.ver # 0 THEN
Kernel.WriteString(", ver ");
j := 30; WHILE (j # 16) & ~ODD(ASH(dev.id.ver, -j)) DO DEC(j) END;
Kernel.WriteInt(j-16, 1); Kernel.WriteChar(".");
Kernel.WriteInt(dev.id.ver MOD 10000H, 1)
END;
Kernel.WriteLn
END
END
END ShowDevices;
PROCEDURE InitControllers;
VAR i: LONGINT; ctrl: Controller;
BEGIN
FOR i := 0 TO MaxControllers-1 DO
ctrl := controller[i];
Kernel.WriteString("IDE"); Kernel.WriteInt(i*2, 1);
Kernel.WriteString(".."); Kernel.WriteInt(i*2+1, 1); Kernel.WriteString(": ");
IF ctrl # NIL THEN
Kernel.WriteInt(ctrl.irq, 1); Kernel.WriteHex(ctrl.port, 9); Kernel.WriteHex(ctrl.port2, 9);
Kernel.WriteChar(" ");
IF ResetController(ctrl) THEN
Kernel.WriteString("reset ok"); Kernel.WriteLn;
IF ~(ctrl.irq IN irqs) THEN
Kernel.InstallIP(InterruptHandler, SHORT(Kernel.IRQ + ctrl.irq));
INCL(irqs, ctrl.irq)
END
ELSE
controller[i] := NIL;
IF ~TraceStatus THEN
Kernel.WriteString("reset failed"); Kernel.WriteLn
END
END
ELSE
Kernel.WriteString("disabled"); Kernel.WriteLn
END
END
END InitControllers;
PROCEDURE InitBusMaster;
VAR bus, dev, fkt, i, bmbase, iobase: LONGINT; s: SET; str: ARRAY 8 OF CHAR;
PROCEDURE FindDevice(id, vendor: LONGINT): BOOLEAN; (* set bus, dev, fkt as side-effect *)
VAR res: LONGINT;
BEGIN
res := PCI.FindPCIDevice(id, vendor, 0, bus, dev, fkt);
RETURN res = PCI.Done
END FindDevice;
PROCEDURE ReadDWord(adr: LONGINT; VAR s: SET);
VAR res: LONGINT;
BEGIN
res := PCI.ReadConfigDword(bus, dev, fkt, adr, SYSTEM.VAL(LONGINT, s));
IF res # PCI.Done THEN s := {} END
END ReadDWord;
PROCEDURE WriteByte(adr: LONGINT; s: SET);
VAR res: LONGINT;
BEGIN
res := PCI.WriteConfigByte(bus, dev, fkt, adr, SYSTEM.VAL(LONGINT, s));
(* ignore res *)
END WriteByte;
BEGIN
IF BMEnabled THEN
Kernel.GetConfig("ATABM", str);
IF str[0] # "0" THEN
IF FindDevice(7010H, 8086H) OR FindDevice(7111H, 8086H) OR
FindDevice(2411H, 8086H) OR FindDevice(2421H, 8086H) THEN
ReadDWord(PCI.CmdReg, s);
IF OverrideBIOS & (s * {0,2} = {0}) THEN (* override BIOS-disabled BM setting *)
Kernel.WriteString("Overriding BIOS bus-master setting"); Kernel.WriteLn;
WriteByte(PCI.CmdReg, s + {2});
ReadDWord(PCI.CmdReg, s)
END;
IF s * {0,2} = {0,2} THEN (* ports & BM enabled *)
ReadDWord(20H, s); (* BMIBA *)
bmbase := SYSTEM.VAL(LONGINT, s * {4..15});
IF bmbase # 0 THEN
ReadDWord(40H, s); (* IDETIM *)
FOR i := 0 TO 1 DO (* primary and secondary controller *)
IF i = 0 THEN iobase := 1F0H ELSE iobase := 170H END; (* standard ports *)
IF (15 IN s) & (controller[i] # NIL) & (controller[i].port = iobase) THEN
Kernel.WriteString("IDE"); Kernel.WriteInt(i*2, 1);
Kernel.WriteString(".."); Kernel.WriteInt(i*2+1, 1);
Kernel.WriteString(": Bus-master enabled"); Kernel.WriteLn;
controller[i].bmbase := bmbase + 8*i;
NEW(controller[i].prdt)
END;
s := SYSTEM.LSH(s, -16)
END
ELSE
Kernel.WriteString("Bus-master ports disabled (BIOS)"); Kernel.WriteLn
END
ELSE
Kernel.WriteString("Bus-master disabled"); Kernel.WriteLn
END
ELSE
(*Kernel.WriteString("Bus-master chipset not detected"); Kernel.WriteLn*)
END
END
END
END InitBusMaster;
(* Main transfer procedure. *)
PROCEDURE Transfer(d: Disks.Device; op, lba, num: LONGINT; VAR data: ARRAY OF CHAR; ofs: LONGINT; VAR res: LONGINT);
VAR dev: Device; ctrl: Controller; num1, try, bufAdr: LONGINT; pkt: Packet16; read: BOOLEAN;
BEGIN
IF TraceCalls THEN Kernel.WriteString(d.name); Kernel.WriteString(" Transfer"); Kernel.WriteLn END;
IF (op = Disks.Read) OR (op = Disks.Write) THEN
read := op = Disks.Read;
dev := d(Device); bufAdr := SYSTEM.ADR(data[ofs]);
IF dev # NIL THEN
IF (lba >= 0) & (num >= 0) & ((lba < dev.size) & (lba+num <= dev.size) OR (RemovableBit IN dev.id.type)) THEN
ASSERT(num*dev.blockSize <= LEN(data)-ofs); (* range check *)
ctrl := dev.controller;
SYSTEM.CLI();
IF ctrl.busy THEN SYSTEM.STI(); SYSTEM.HALT(17) END;
ctrl.busy := TRUE;
SYSTEM.STI();
res := SelectDevice(ctrl.port, dev.dev, SelectTimeout);
IF (res = 0) & ~dev.init THEN (* initialize *)
res := InitDevice(ctrl.port, ctrl.port2, dev.dev, dev.id.type, dev.chs);
dev.init := res = 0
END;
IF (res = 0) & (RemovableBit IN dev.id.type) THEN res := CheckRemovable(dev, read, lba, num) END;
WHILE (res = 0) & (num > 0) DO
try := MaxTries; num1 := MaxTransfer;
IF num1 > num THEN num1 := num END;
REPEAT
IF AtapiBit IN dev.id.type THEN
IF read THEN ComposePacket(pkt, 28X, lba, num)
ELSE ComposePacket(pkt, 2AX, lba, num)
END;
res := TransferPacket(dev, pkt, read, bufAdr, num*dev.blockSize)
ELSE
IF (ctrl.bmbase # 0) & ~ODD(bufAdr) THEN
res := TransferDMA(dev, read, lba, num1, bufAdr)
ELSE
IF read THEN res := ReadPIO(dev, lba, num1, bufAdr)
ELSE res := WritePIO(dev, lba, num1, bufAdr)
END
END
END;
DEC(try)
UNTIL (res = 0) OR (try = 0);
INC(lba, num1); DEC(num, num1); INC(bufAdr, BS*num1)
END;
ctrl.busy := FALSE
ELSE
res := 26
END
ELSE
res := 11
END
ELSE
res := Disks.Unsupported
END
END Transfer;
PROCEDURE GetSize(d: Disks.Device; VAR size, res: LONGINT);
VAR dev: Device;
BEGIN
dev := d(Device); res := 0;
IF TraceCalls THEN Kernel.WriteString(d.name); Kernel.WriteString(" GetSize"); Kernel.WriteLn END;
IF RemovableBit IN dev.id.type THEN
res := CheckRemovable(dev, FALSE, 0, 0);
IF res = Disks.MediaChanged THEN res := 0 END
END;
IF res # 0 THEN
size := 0
ELSIF AtapiBit IN dev.id.type THEN
size := dev.size;
res := 0
ELSE
size := dev.getpar.cyls*dev.getpar.hds*dev.getpar.spt;
res := 0
END
END GetSize;
PROCEDURE Handle(d: Disks.Device; VAR msg: Disks.Message; VAR res: LONGINT);
VAR dev: Device;
BEGIN
dev := d(Device);
IF msg IS Disks.GetGeometryMsg THEN
IF TraceCalls THEN Kernel.WriteString(d.name); Kernel.WriteString(" Handle/GetGeometry"); Kernel.WriteLn END;
IF dev.getpar.spt # 0 THEN
WITH msg: Disks.GetGeometryMsg DO
msg.cyls := dev.getpar.cyls; msg.hds := dev.getpar.hds; msg.spt := dev.getpar.spt;
res := Disks.Ok
END
ELSE
res := Disks.Unsupported
END
ELSIF msg IS Disks.LockMsg THEN
IF TraceCalls THEN Kernel.WriteString(d.name); Kernel.WriteString(" Handle/Lock"); Kernel.WriteLn END;
IF (RemovableBit IN dev.id.type) THEN
res := LockMedium(dev, TRUE)
ELSE
res := Disks.Unsupported
END
ELSIF msg IS Disks.UnlockMsg THEN
IF TraceCalls THEN Kernel.WriteString(d.name); Kernel.WriteString(" Handle/Unlock"); Kernel.WriteLn END;
IF (RemovableBit IN dev.id.type) THEN
res := LockMedium(dev, FALSE)
ELSE
res := Disks.Unsupported
END
ELSIF msg IS Disks.EjectMsg THEN
IF TraceCalls THEN Kernel.WriteString(d.name); Kernel.WriteString(" Handle/Eject"); Kernel.WriteLn END;
IF (RemovableBit IN dev.id.type) THEN
res := RemoveMedium(dev)
ELSE
res := Disks.Unsupported
END
ELSE
IF TraceCalls THEN Kernel.WriteString(d.name); Kernel.WriteString(" Handle/others"); Kernel.WriteLn END;
res := Disks.Unsupported
END
END Handle;
PROCEDURE Register;
VAR i: LONGINT; dev: Device;
BEGIN
FOR i := 0 TO MaxDevices-1 DO
dev := device[i];
IF dev # NIL THEN
dev.flags := {};
IF RemovableBit IN dev.id.type THEN INCL(dev.flags, Disks.Removable) END;
dev.transfer := Transfer; dev.getSize := GetSize; dev.handle := Handle;
Disks.Register(dev)
END
END
END Register;
(** The install command has no effect, as all ATA devices are installed when the module is loaded. *)
PROCEDURE Install*;
END Install;
BEGIN
Kernel.WriteString("ATADisks 08.12.2000 by cp, pjm, prk"); Kernel.WriteLn;
irqs := {}; Kernel.InstallTermHandler(Cleanup);
IdentifyControllers;
InitControllers;
IdentifyDevices;
ShowDevices;
(*InitControllers*); (* re-initialize controllers after identify *)
InitBusMaster;
Register
END ATADisks.
Error codes:
1 device select failed before issueing
2 device select failed after issueing
3 pio read failed
4 pio read error
5 pio write failed
6 pio write error
7 dma transfer timeout
8 dma transfer failed
9 dma transfer error
10 controller re-entered
11 device does not exist
12 identify atapi failed
13 device size is 0
14 identify failed
15 bad controller port
16 atapi reset failed
17 ata set parameters failed
18
19 pio read timeout
20 pio read error
21 pio read error
22 pio write error
23 pio write timeout
24 pio write error
25 identify ata geometry bad
26 transfer out of range
27 no media
28 media write protected
29 media unlock failed
30 sync cache failed
31 packet command failed
32 transfer packet error (did not complete)
33 transfer failed (no sense data available)
34 transfer failed (sense data available)
35 rmsn failed (not supported)
36 read capacity packet failed
37 unit attention failed
38 get status failed
39 remove ata medium failed
ATADisks.Install System.Free ATADisks ~
ATAErrors.Text
to do:
o check selected device
o atapi identify with interrupt
o set ReadOnly bit in device.flags depending on removable media status for non RMSN devices